Dialogic D/120JCT-LS

D120JCTLS Telephony Card

Technical Specs

• System size: Small-to-Medium Enterprise
• Form factor: PCI
• Ports: 12
• Network interface: Onboard loop start interface

Resource Bus::

• H.100
• CT Bus
• SCbus with adapter

Operating Systems:

• Linux*
• Windows NT
• Windows 2000
• Windows XP
• Windows 2003

Signaling:

• DTMF
• MF

Key Features:

• Supports DSP-based onboard fax and host-based speech recognition to maximize the number of boards in the system
• Supports G.726 bit exact and GSM coders, letting developers implement unified messaging applications that meet VPIM standards
  With a variety of international approvals, the board expands an application's ability to serve several global market segments at no extra cost
• Supports continuous speech processing, a flexible speech processing technology, which when coupled with efficient drivers, off-loads critical real-time signal processing in speech-enabled applications to onboard DSPs
• Support for Simple Network Management Protocol (SNMP) software, used for remote CT board diagnostics/management
• Earth Recall capability provides support for switches in the UK in addition to complementing existing infrastructure
• Full support of Japanese CID, including the ability to detect polarity reversals while online

Applications:

• Applications Interactive media response
• Web-enabled contact center
• Unified messaging
• Speech-enabled auto-attendant
  

Market Names:

• D120JCTLSU (for 5 V and 3.3 V PCI slot support)
• D120JCTLSUJP (universal PCI for use in Japan)
• D120JCTLSUCN (universal PCI for use in China)
• D120JCTLSUIN (universal PCI for use in India)
• D120JCTLSUEU2 (universal PCI for use in Europe, Australia, and New Zealand)

Detailed Technical Specifications: Number of ports 12 Maximum boards/operating system 8 (Linux*, Windows* NT, Windows 2000, Windows* XP, Windows 2003). Number may be limited by application and system performance. CT Bus loads per board 1 Maximum CT Bus loads per system 20 Analog network interface Onboard loop start interface (12) Resource sharing bus CT Bus Control microprocessor Intel® 80486 GXSF running at 32.768 MHz with 2 MB SDRAM Digital signal processors Two Motorola* DSP 56303 (Onyx) @ 100 MHz, 24-bit, each with 256 K word private SRAM Host Interface Bus compatibility PCI compatible. Complies with PCISIG Bus Specification, Rev. 2.2. Bus speed 33 MHz maximum Bus mode 32-bit Shared memory 32 KB to 64 KB page Interrupt level One IRQ is shared by all D/120JCT-LS boards I/O ports None Telephone Interface Trunk type Loop start Ground start for inbound applications with AC ringing Impedance 600 Ohms nominal Ring detection 40 Vrms to 130 Vrms, 15.3 Hz to 68.0 Hz Loop current range 20 mA to 60 mA, (Euro) 20 mA to 120 mA, polarity insensitive Echo return loss 17 dB min. (at country impedance) Crosstalk coupling >-75 dB Speech digitization 64 Kb/s, µ-law PCM (companding to ADPCM performed in Spring Ware) Frequency response 300 Hz to 3400 Hz ±3 dB Connector RJ-25, 6-port, 6-position Encironmental Requirements +5 VDC 1.2 A typical, 1.4 A max. +12 VDC 235 mA typical, 285 mA max. –12 VDC 80 mA max., 100 mA max. Operating temperature 0°C to +50°C Form factor Universal slot (5 V or 3.3 V) PCI long card 12.28 in. (31.2 cm) long 4.2 in. (10.67 cm) high Safety and EMC Certifications Approvals Canada ICES-003 Class A ULc CSA 950 File E96804 Europe EN60950 EN55022 EN55024 Japan VCCI Class A United States FCC Part 15 Class A UL 1950 File E96804 International IEC60950 CISPR 22 CISPR 24 Telecom Approvals Canada IC: 885 10540 A European Union DoC 06/30/2003 Japan A00-0318JP United States US:EBZUSA-34827-KX-N Reliability/Warranty Estimated MTBF 154,000 hours per Bellcore* Method Warranty 3 years Spring Ware Firmware Technical Specifications: Facsimile Fax compatibility ITU-T G3 compliant (T.4, T.30) ETSI NET/30 compliant Maximum data rate 14,400 b/s (v.17) send 9600 b/s (v.29) receive receive Variable speed selection Automatic step-down to 12,000 b/s, 9600 b/s, 7200 b/s, 4800 b/s, and lower Transmit data modes Modified Huffman (MH) Modified Read (MR) Receive data modes MH, MR File data formats Tagged Image File Format (TIFF/F) for transmit/receive MH and MR ASCII-to-fax conversion Host-PC-based conversion Direct transmission of text files All Windows fonts supported Page headers generated automatically Error correction Detection, reporting, and correction of faulty scan lines Image widths 8.5 in. (21.5 cm) 10.0 in. (25.5 cm) 11.9 in. (30.3 cm) Image scaling Automatic horizontal and vertical scaling between page sizes Polling modes Normal Turnaround Image resolution Normal (203 pels/in. × 98 lines/in.) (203 pels/2.54 cm × 98 lines/2.54 cm) Fine (203 pels/in. × 196 lines/in.) (203 pels/2.54 cm × 196 lines/2.54 cm) Fill minimization Automatic fill bit insertion and stripping Audio Signal Receive range –40 dBm to –7 dBm nominal, configurable by parameter** Automatic gain control Application can enable/disable Above –22 dBm results in full-scale recording, configurable by parameter** Silence detection –40 dBm nominal, software adjustable** Transmit level (weighted average) –9.5 dBm nominal, configurable by parameter** Transmit volume control 40 dB adjustment range, with application-definable increments and legal limit cap Frequency Response 24 Kb/s 300 Hz to 2600 Hz ±3 dB 32 Kb/s 300 Hz to 3400 Hz ±3 dB 48 Kb/s 300 Hz to 2600 Hz ±3 dB 64 Kb/s 300 Hz to 3400 Hz ±3 dB Audio Digitizing 13 Kb/s GSM @ 8 kHz sampling 24 Kb/s OKI* ADPCM @ 6 kHz sampling 32 Kb/s OKI ADPCM @ 8 kHz sampling 32 Kb/s G.726 @ 8 kHz sampling 48 Kb/s µ-law PCM @ 6 kHz sampling 64 Kb/s µ-law PCM @ 8 kHz sampling Digitization selection Selectable by application on function call-by-call basis Playback speed control Pitch controlled Available for 24 Kb/s and 32 Kb/s data rates Adjustment range: ±50% Adjustable through application or programmable DTMF control DTMF Tone Detection DTMF digits 0 to 9, *, #, A, B, C, D per Bellcore LSSGR Sec 6 Dynamic range -38 dBm to –3 dBm per tone, configurable by parameter** Minimum tone duration 40 ms, can be increased with software configuration Interdigit timing Detects like digits with a >40 ms interdigit delay Detects different digits with a 0 ms interdigit delay Twist and frequency variation Meets Bellcore LSSGR Sec 6 and EIA 464 requirements Noise tolerance Meets Bellcore LSSGR Sec 6 and EIA 464 requirements for Gaussian, impulse, and power line noise tolerance Cut-through Local echo cancellation permits 100% detection with a >4.5 dB return loss line Talk off Detects less than 20 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). Detects 0 digits while monitoring MITEL speech tape #CM 7291. Global Tone Detection Tone type Programmable for single or dual Max. number of tones Application-dependent Frequency range Programmable within 300 Hz to 3500 Hz Max. frequency deviation Programmable in 5 Hz increments Frequency resolution ± 5 Hz. Separation of dual-frequency tones is limited to 62.5 Hz at a signal-to-noise ratio of 20 dB. Timing Programmable cadence qualifier, in 10 ms increments Dynamic range Programmable, default set at –6 dBm to –3 dBm per tone Global Tone Generation Tone type Generate single or dual tones Frequency range Programmable within 200 Hz to 4000 Hz Frequency resolution 1 Hz Duration 10 ms increments Amplitude –43 dBm to –3 dBm per tone nominal, programmable MF Signaling MF digits 0 to 9, KP, ST, ST1, ST2, ST3 per Bellcore LSSGR Sec 6, TR-NWT-000506 and CCITT Q.321 Transmit level Complies with Bellcore LSSGR Sec 6, TR-NWT-000506 Signaling mechanism Complies with Bellcore LSSGR Sec 6, TR-NWT-000506 Dynamic range for detection –25 dBm to –3 dBm per tone Acceptable twist 6 dB Acceptable frequency variation Less than ±1 Hz Call Progress Analysis Busy tone detection Default setting designed to detect 74 out of 76 unique busy/congestion tones used in 97 countries as specified by CCITT Rec. E., Suppl. #2 Default uses both frequency and cadence detection Application can select frequency only for faster detection in specific environments Ring back detection Default setting designed to detect 83 out of 87 unique ring back tones used in 96 countries as specified by CCITT Rec. E., Suppl. #2 Uses both frequency and cadence detection Positive voice detection accuracy >99% based on tests on a database of real world calls in North America Performance in other markets may vary Positive voice detection speed Detects voice in as little as 1/10th of a second Positive answering machine detection accuracy >85% based on application and environment Fax/modem detection Pre-programmed Intercept detection Detects entire sequence of the North American tri-tone Other intercept tones sequences can be programmed Dial tone detection before dialing Application enable/disable Supports up to three different user-definable dial tones Programmable dial tone drop out debouncing Tone Dialing DTMF digits 0 to 9, *, #, A, B, C, D per Bellcore LSSGR Sec 6, TR-NWT-000506 Frequency variation Less than ±1 Hz Rate 10 digits/s maximum, configurable by parameter** Level –4.0 dBm per tone, nominal, configurable by parameter** Pulse Dialing 10 digits 0 to 9 Pulsing rate 10 pulses/s, nominal 20 pulses/s for Japan, configurable by parameter** Break ratio 60% nominal, configurable by parameter** Analog Caller Identification Applicable standards Bellcore TR-TSY-000030 Bellcore TR-TSY-000031 TAS T5 PSTN1 ACLIP: 1994 (Singapore) Modem standard Bell 202 or V.23, serial 1200 bits/sec (simplex FSK signaling) Receive sensitivity -48 dBm (-50 dBv) to -1 dBm Noise tolerance Minimum 18 dB SNR over 0 to -48 dBm dynamic range for error-free performance Data formats Single Data Message (SDM) and Multiple Data Message (MDM) formats via API calls and commands Line impedance AC coupled 600 Ohm (@ 1.8 kHz) termination during Caller ID on-hook detection interval Message formats ASCII or binary SDM, MDM message content   Analog Display Services Interface (ADSI)   FSK generation per Bellcore TR-NWT-000030 CAS tone generation and DTMF detection per Bellcore TR-NWT-001273. ** Analog levels: 0 dBm0 corresponds to a level of +3 dBm at tip-ring analog point. Values vary depending on country requirements; contact your account manager. 1 Average speech mandates +16 dB peaks above average and preserves -13 dB valleys below average.